Vacuum Forming Machine for Pallect

Vacuum Forming Machine for Pallect

I,Operate basic principle
Using the thermoplastic sheet is heated and softened in the mildew for vacuum molding, turn out to be necessary products. Their function is the clip – heating – forming – merchandise.

II,Characteristics
01. CZPT, pneumatic, electrical integration. Each motion program managed by the PLC. Touch-screen procedure, easy and hassle-free.
02. Loading less complicated, significantly less scrap molding materials cost savings.
03. Heater motor, frequency management, large-speed exact and stable.
04. CZPTtric furnace temperature handle program is fully computerized smart computerized compensation manage, partitioning a controlled man-machine interface of a electronic enter, with substantial precision fine-tuning, temperature uniformity, quickly heating (just 5 minutes from -four hundred degrees), secure ( impact from external voltage, temperature fluctuations of not far more than 1 diploma), reduced vitality use (preserving about fifteen%), lengthy existence plate stove, electrical bricks and so on. instantly detected.
05. Ideal convex molding, molding height, steady item high quality.
06. The mould seat with electric limit adjustment, adjust speedily and very easily.
07. Device is geared up with air-cooling system that enables products to cool more quickly and far better styling.
08. Production counts, or can be established to routinely shut down ahead of the law enforcement, with file memory function, can keep up to 230 product parameter info
09. The die table utilizing mosaic lubricated bearings, flexibility of motion and precise.
10. Die clip structure actions and synchronized by the rack and pinion construction linkage, the lifting synchronization, extending cylinder life
11. Operating side making use of basic safety grating products to guarantee the security of the operator misuse.
 
 III,CZPT parameters

Parameter XCH130/one hundred ten/thirteen.5(manner No.)
Max. forming location (mm2) 1300mm*1100mm
Min.forming region (mm2) 1200mm * 1000mm
Sheet requirements (Max.)   1370mm * 1170mm
Thickness of sheet applied   .eight-3mm
Max. molding height   135mm
Capacity   1-3 (instances/min)
Gasoline supply Air consumption (m3/min)     ≥ 2
Pressure   .6Mpa(inlet .eight-1Mpa)
Vacuum pump (Outlay)    Busch R5 5710
Power    three-period 4-wire 380V / 220V 50Hz
CZPT power   64KW
Proportions ( L × W × H) (mm)    4200 * 2410 * 2900
 Total weight (Kgs)    4000

 
 
IV,CZPT configuration

Programmable logic controller (PLC)   ZheJiang Delta
Touch display screen check
(10.four “inch / Coloration)  
ZheJiang Delta
CZPT    ZheJiang Delta
Feeding motor   China
Heater   (99pcs) China
Solid condition relay AC contactor    Germany Siemens
Thermo relay   Japan Omron
Vacuum pump   Busch R5 5710
pneumatic components   South Korea
Cylinder    China
Admirer blower   China

V,Set up Recommendations
one. The machine must be set up in a dry, clean store flooring. And leave some apart installation location of the lively working distance gasoline, electrical energy, refer to the equipment diagram of a flat placement.
two. Soon after getting rid of the packaging machine, positioned on the floor degree of the agency can use. Its region, see the physical appearance of area dimensions Determine II.
3. Ended up related to a supply of drinking water and gasoline provide, and connect the floor wire.
4. Verify heater heating components are intact (Ruoyin delivery injury should be replaced).
5. All lubrication factors should be included to lubricants. Vacuum pumps, air supply FRL oil amount should appear on to the line. The watershed of the filter system slop set the internet.
6. Verify the vacuum pump motor, cooling fan rotation is proper (soon after electrical power check, which if not effectively swap two wires can).
seven. CZPT part of the user’s machine to set up their own gas purification equipment, in purchase to guarantee elevated service daily life of pneumatic elements. Please refer to the pneumatic equipment thoroughly clean air method movement chart diagram III.
eight. External electricity cable with double insulated copper wire 4, every single part is not considerably less than 16mm2.

VI,Sample Photograph

VII,Certifications

VIII,Workshop Photographs

 
IX,Package deal

X,Exhibition

 

Vacuum Forming Machine for Pallect